AmateurRadio.com

Well G3XBM is always reminiscing about his time at PYE, I wish I could do the same for Thorn Automation days, but as most of the work was restricted very little of their products have made it into the Amateur world. .

Rogers recent ramble here made me reach for the desk drawer. Out I pulled a PF1 receiver still complete with case.



I cut my teeth on a PF1 with my first taste of 70cm receive back in the early 1980's. What I seem to remember I picked  up quite a few of these at a radio rally for about £5 each! But the crystal was about the same price again, which was required to replace the original to get them working on one lonely channel, or tuned up on a single repeater frequency, in my case being Stafford GB3ZI (433.275MHz). What I seem to remember tune up was quite a fiddle, they used to break into oscillation, as the pull was quite a bit out of the zone of where they had originally been working in the commercial world.






This one has seen better days, but most of it is still quite complete apart from the metal shield over the front end. The battery was rechargeable 9V long time expired, but soldering in a 3F23 or PP3 would make it burst into life. So as you can see I have been around quite a while to remember the older PYE generation, but not quite as long as G3XBM. :-)

When I started in this hobby when I was around 7, it was batteries and old car bulbs nicked from my Dad's shed, with wires held on the terminals with sellotape, that was to give me my first taste of electronics, well before I  even started making crystal sets. That is all what is needed,just a little encouragement to spark enthusiasm in our hobby, little did I know then I would have held a job in the industry and have an Amateur Radio licence to my name and I would be writing about it today.


So I was in my local discount store the other day, something caught the corner of my eye, an electronic kit. Tronex 50+ Circuit Lab. Made in, you guess right China! But does similar to what I have mentioned above. Yes it resembles the kits that were once produced in late 70's, where wires were held under springs to connect each component into the circuit.



Only having two daughters, one whom is now married, and the other that is now in her latter years of High school, a chance perhaps to encourage her, and get her away from playing with her tablet and computer during the long hours of these dark nights. So I decided to buy one for her Christmas stocking. My wife said you only bought it so you can play with it didn't you? I said no, this is a good educational tool and can be used to encourage, especially with her having to do a science at school.






Not hopeful she will be another Ham in the future, but you never know where it will lead? For overseas readers of my blog I notice there are Tronex kits on ebay of similar content.

I will return to this when she decides to investigate and play, further info here:

https://www.homebargains.co.uk/products/14749-tronex-50-circuit-lab.aspx

Some idiot today decided to Spam the comment section of my Blog with advert links, nothing to do with Amateur radio, this is not the first time this has happened. So I have now taken action and set all comments to be moderated by myself before they are released. Just stupid people that have caused me to take this unnecessary lock out and create me more work than I need.

Spam as much as you want but they will be destroyed!

You have been warned !

With constructors and hobbists looking at sourcing electronic components, even the hard to get stuff along with a bit of added value for money.  I have started a component list with suppliers from the far East.


Access it from the top right under Pages: Far East Component suppliers.


Or from this link: http://g1kqh.blogspot.com/p/far-east-component-suppliers.html



Hope you all find it useful?

QRP Labs started design and producing small QRSS/WSPR Beacon transmitters some years ago, along with a complete set of addons and other accessories that have evolved as the project progressed.  Last year, owner and designer of QRP Labs, Hans Summers, took his small company to a new success level with the launch of the QCX 5W Single Band CW/WSPR transceiver. Which has currently sold to date well over 5500 units, over various HF bands.  A fantastic project because it crammed so many full features into it's small pcb, including its inheritance from the WSPR Beacon, but with full frequency agility, CW decoder and included was a unique inbuilt test generator to aid alignment, never seen on such a low price product before.

The QCX has proved a QRP Labs British success story for such a niche product in it's own right.

Of course Hans (G0UPL) wasn't going to rest on his laurels and an SSB radio had been rumoured to be on the design board for quite sometime. Infact he had told me at the begining of this year, these projects takes a while before they hop off the design board and reach fruition to complete into a working project.


So it wasn't no surprise that G0UPL has again used YOTA 2018 (Youngsters On The Air) hosted in South Africa this year, to pre launch the QSX a 10 Band HF SDR project. You could say that YOTA is used like a test bed to iron out any last minute technical and constructional difficulties, found, or encountered, before he begins to put the kit into full time mass production in a couple of months or so. Most of what the new SDR single/10 band rig will do and it's outlined specification, is set out on his website here: QRP LABS - QSX




I was fortunate enough to have a short electronic messaging chit chat with Hans earlier this week, and he was able to put me well in the picture with one or two technical details about the project.

While emissions and spurs are all the the talk of the town at the moment on another QRP project from another company not associated with QRP-Labs . The QSX will have "no" spuri issues!

Using 2 IRF510's in the QSX's linear HF PA, Hans reports the performance is excellent! The PA module being driven by two BS170's in Push Pull, giving an overall gain of around 26-28dB. This concludes in easily producing 10W across all HF bands using 12V.

Gain Flatness is better than 2dB across the spectrum between 2-30MHz. It is about 4dB down at 6m and 8dB down at 4m.Thus the same drive level that produces 10W across the HF bands gives a very useable 5W on the 6m band.

Hans also reports the linearity is excellent too!

Harmonics are low even before it even enters the LPF: 80m measurements 2nd harmonic is at -38dBc, 3rd -31dbC Making it very easy for the LPF to clean up what remains and make it a very high performance radio.

All this is acheived using cheap Chinese IRF510's





The heatsink is BIG!! Testing, it ran at 10W output for 1 hour continous 100% duty cycle, no forced air or cooling, the heatsink temperature was still reasonable about 40C over ambient.

Destruction tested at:

1) 20V supply.
2  25W output.
3) 15W 100% duty cycle for 15 mins.
4) Open load.
5) Short circuit.
6) Various mismatches.

All tests resulted in no failure.

Sorry there has been very little activity from me during the last few months, family stuff has taken up a lot of my spare time recently, and radio has been well off the menu. However I will try and get back into the Blog as our Summer comes to an end.

I was recently contacted by one of the Telford Hamfest organisers asking me to give a talk:

 We would like to invite you to give a "talk" at our "Telford Hamfest" QRP, orientated, would be great. The date for our Hamfest is Sunday September 2nd 2018. We expect to put on three "Talks". The "Talks" would last about 40(ish), minutes, with a Q&A after each, with a gap until the next talk. The timings are 11.30,12.30 and 13.30. I hope you are able to take us up on our offer Steve
--------------------

The Telford Hamfest is a Radio rally which has been held around the Telford area for many years at various venues. But for a number of years has stabilised at being held at Coalbrookdale, Shropshire, and also now incorporates the G-QRP Convention as an added bonus.

Well Stephen had already decided he wasn't going to the Hamfest this year, so it all arrived too late! But it is with interesting thought what I would of talked about, and who actually put me up for this, I could name a few?

The last lecture I gave is when I ran a Packet radio BBS and node (GB7RUG) some 20 years ago. Talks don't just come together overnight, sorry I had no real time to prepare anyway. So Telford Radio club and G-QRP thanks for asking, I might do it next year if you give me enough time to think about it?

Actually by now I have mulled it over I have even thought in my dreams what I would of chatted about Hmmm! Humm!

See you all next year :-)

When HF Signals marketed the uBITX early December 2017, customers leapt in and ripped them off the shelf. Who could imagine the small Test facility in India that VU2ESE had setup trying to cope with the unexpected demand, or the women having to wind and test the toroids, churning them out at speed without breaking a finger nail. Even one type of toroid used had to be subsituted, for another, as the world ran out and they couldn't be sourced easily, but still the uBITX somehow was kept on track. A total to date of over 6000 uBITX PCBs sold, with very few bugs reported, apart from one batch with the faulty WX branded TDA2822 audio amp that hit the fan and must of caused an awful headache at the time.

Now that manufacturing has now caught up with demand, and there is no time lag on ordering, the uBITX becomes ex stock along with some new modifications and a new revised r4 PCB.

Could the uBITX get any better well certainly it looks like it does!


Here are the changes from Ashhar Farhan as reported today on Groups.io: