AmateurRadio.com

I ended up staying home, working from the shack and forgoing my bumblebee number. The weather was partly a factor as one minute it was sunny and five minutes later it looked like it was going to downpour.

The real issue was my back. I woke up this morning with a stiff lower back. Nothing incapacitating, but sore enough that hiking to my FOBB destination while carrying all my gear, and then setting up would have been no fun. Added to that was the fact that my sore back has also slowed me down somewhat, so if I would have had to dismantle the station in a hurry, it would have been a problem.

Even from home, on the good antennas, band conditions seemed to stink. I didn’t hear a lot of FOBB’ers, and those I did hear were pretty weak. Giving out a 559 was generous today. I managed to work 15 stations.

I sure hope band and weather conditions and my back are better for the Skeeter Hunt!

72 de Larry W2LJ
QRP – When you care to send the very least!

When we get back from shopping I shall return to JT65-HF and JT9-1 modes hoping to work more stations. Yesterday, staying on 20m, I worked 4 Europeans running 2.5 or 5W. JT65-HF is very intuitive and works well. Althought I have had JT9-1 QSOs on 10m in the past, I suspect the rig stability is “challenging” and JT65-HF gives me a better chance. JT65-HF is some 4dB worse than WSPR but the TX period is only 48 secs (1 minute TX period but actual TX is less) so may be better with QSB?  JT9-1 is a narrower bandwidth mode than JT65-HF and is about 2dB worse than WSPR. Of course, JT65 and JT9 are proper QSO modes.

Sunspot count today is 76 (decent) and 20-30MHz conditions are supposed to be “normal” so there could well be some F2 (as well as Es) on 10m today. JT65-HF and JT9-1 on 10m are calling I think.

The great advantage of WSPR is you can set the rig running and monitor things in another room. JT65 and JT9 seem to require “hands on” operation, which is fine.

My Chinese Li Ion battery “ol’ Blue” (upper right) has given up the ghost, much the same as Mike VE3WDM has written over at his blog.  In my case, the battery will not take a charge.  The output from the wall wart charger is perfect, but no matter how long it’s connected to the battery, the battery itself will not charge.

I suspect either a faulty cell or perhaps a fault with the little regulator board that’s inside the blue shrink wrap. So the decision had to be made.  Even though the price is relatively cheap, do I buy another Chinese battery or try something else? Do I go back to hauling around my small, but heavy, 5 Ah sealed lead acid battery?

I have a charger that will handle 18650 type Li Ion batteries, as these are what go into the tactical flashlights that I keep in my CERT pack and my radio “Go Pack”.  So I figured that since I already have half of what I need, that I would go a different route this time.

I purchased a pack of 10 type 18650 batteries (upper left) from an American vendor.  The ones I bought are 3.7V and have a rating of 5300 mAh.  I also purchased two of the 4 cell holders that you see above. This gives me two 14.8V, 5300 mAh batteries. All I had to do was solder on the connector that goes directly into the KX3.

I tried them out today and they seem to work without any problems.  I will use a fresh charged pack tomorrow for FOBB and will see how long one pack lasts before I have to switch over to the backup pack.

72 de Larry W2LJ
QRP – When you care to send the very least!

This evening I went on 20m JT65 again and managed a couple of European QSOs in reply to the CQs of others. I am using JT65-HF software that is very simple to use. So far I have used the FT817 at either 2.5 or 5W.

JT65-HF screenshot

If you see a station calling CQ (shows up in green) you just click on it to start a QSO with that station. If he copies you and replies then the started QSO shows up in red – all very simple. Wonder if there is a similar (easy) package for JT9-1 on HF?

Looking on PSK Reporter I see plenty of USA stations were copying me too, so it should not be too hard to work DX with just a little effort even with my compromise antenna. When 10m and 6m are open, DX should be easier still.

With JT65-HF and JT9-1,  I have to be in the shack, but at least there is no speaking, saving my poor voice.

The pride and joy in my shack is a Weller WECP-COD3 soldering iron. It is the only professional piece of equipment I have.

Weller soldering iron

So now I wonder: how old is the soldering iron in your shack? Do you go for quality or buy low price and throw it out after a while? Leave a comment if you please. It will surely be fun to read.

Episode 4 from the TX Factor team is a Ham Radio special, filmed entirely on location at this year’s convention in Friedrichshafen on the shores of Lake Constance.

Bob and Mike report on ham radio technology old and new, including a look at the new System Fusion DR-1 144/430 Dual Band C4FM/FM Digital Repeater from Yaesu, and an amazing transceiver from Hilberling.

There’s also a chance to win a Yaesu FT-60E dual-band handie in our first free-to-enter competition.

Visit the website to see the latest episode.

www.txfactor.co.uk

Happy viewing!

WG2Z (5600km) copied me just once at lunchtime – he may have copied me more times if I was operating on the correct frequency initially – but this afternoon 10m has been in excellent Es shape today with stations from across the continent copyable after lunch with a few G stations copied out to 184km by tropo or plane reflection.

10m WSPR unique reports since lunch today (repeats not shown)