Posts Tagged ‘General’
AmateurLogic 188: Christmas Celebration and Hotspot Upgrades
December 16th, 2023 | 
Author:
AmateurLogic.TV Episode 188 is now available for download.
AmateurLogic’s Annual Christmas Extravaganza. Tommy upgrades his N5BOC Hotspot with a new Raspberry Pi Zero 2 W and it’s fast. Emile updates his hotspot with the WPSD Project. ALTV’s 2023 Gift Guide for last minute shoppers and slackers. Sampling the tastes of the holidays.
The Art of DX Pileup Busting
SOME INFORMAL THOUGHTS ON WORKING CW DX
Recently, I came across some questions another amateur radio operator posed to a group of CW enthusiasts. Since I have an interest in Morse code, I thought I would explore these questions:
— begin quote —
1. When chasing some particular CW DX station needed for my DXCC punch-list, what are some things(s) that one can do to improve one’s chances of snagging that DX contact amidst a congested pileup? Is it truly the luck of the draw or roll of the dice? Or are there some time tested methods, less than obvious, that the experienced CW DX chasers have used that seem to improve one’s chances of snagging the DX contact? Yes, I’m aware that there are many variables to consider. I’m just looking for some general suggestions to improve my odds of success based on the experience of others.
2. If, let’s say, a DX station appends “UP 1” or “QSX 2” to his CQ call or just “UP” appears in a DX cluster spot listing, what is considered an acceptable amount of “UP”? I’m amazed sometimes at the amount of “UP” that I hear. LOL. Does a hefty amount of “UP” actually improve one’s chances? What does the DX op expect?
3. After a DX station sends their callsign how long should one wait to reply with one’s callsign? I hear stations respond immediately. But sometimes I hear others wait just a “bit”, and then respond to DX. And sometimes when the DX station is responding to a chosen station, other callers are STILL calling the DX op. What do most DX operators expect with regard to the response of a reply? Immediate? One-Mississippi …?
4. I hear stations reply to DX with their callsign once. Others sometimes twice. If I send my callsign twice I run the risk that the DX station has already begun his reply back to me with my sig-report while I’m still in the midst of sending my 2nd callsign reply. So … I should send my call just once?
— end quote–
Great questions! And, the answers translate over to working DX pileups on voice, too.
Here are some of my off-the-cuff remarks, based on my limited experience DXing since 1990:
(I am an avid DXer, with 8BDXCC, etc.)
1. Listen, Listen, Listen: The DX station typically does work split – the DX station on, say, 14.023 MHz, and the DX station is listening anywhere from 14.028 to 14.033 (up 5 to 10). You first, of course, need to listen to the DX station, but, also to hear the stations that are calling the DX station! The trick is to be able to hear some of the stations that are piling up on the DX, and to determine if the DX is working a station, then tunes up a little, or down a little, from the frequency on which the last caller was chosen.
Once you know this, you want to position your signal so that the DX operator tunes to or very near where you are transmitting your signal. If the DX station does not call you but continues in the same tuning direction, you reposition your transmit frequency (always in the pileup window) and try again. If you do not know where the DX station is listening next, and especially if you cannot HEAR the DX station, you are calling blind and are in for a long effort.
If you have a way to see the waterfall at and around the DX frequency, you can often see the general spread of “UP” where the callers congregate. When listening (and, let me tell you, listening is key) to the DX station, watch the waterfall for the responding caller (the station in the pile-up calling the DX), as sometimes it is very obvious who is answering the DX. Watch this exchange for a number of new callers – and get a sense of HOW the DX operator is moving through the pile-up. Anticipate where the DX might listen next. Choose that “next frequency in the pattern of movement” and use that as your calling frequency.
2. Timing your call: this takes a bit of effort. I typically listen to my chosen transmit frequency, trying to call never at the exact same time as others, on or near my calling frequency.
3. I always send my callsign TWICE… something like this:
DX: DX1ABC UP
ME: NW7US NW7US
DX: NW7US 5NN
ME: R R NW7US 5NN TU
DX: NW7US TU, DX1ABC UP
There are some fine CW-oriented DXing books, PDFs, and websites that talk about this. For instance:
http://sota-dl.bplaced.net/articles/cw_chasing_tips_for_newcomers.pdf
https://www.cadxa.org/getting-started-in-dxing.html
I hope this personal observation of mine about working a Morse code pileup is helpful in some way.
73 de NW7US
https://NW7US.us
..
AmateurLogic 187: Buck/Boost, Balun & M5 Ham Radio
AmateurLogic.TV Episode 187 is now available for download.
Tommy builds the M5 Ham Radio project. George makes a high quality 4:1 Balun. Mike assembles a Buck/Boost converter device for use with QRP operations.
AmateurLogic 186: 18 Years of AmateurLogic
AmateurLogic.TV Episode 186 is now available for download.
AmateurLogic.TV celebrates 18 years on the air.
George reviews the Craftsman Battery Powered Soldering Iron.
Jocelyn demonstrates the MFJ-1898 Portable HF + 6 Meter Antenna.
Emile introduces Outlook Package Message Manager.
Mike explores OpenWebRX +.
Announcing the winner of our 18th Anniversary contest and Icom IC-705 prize package giveaway.
AmateurLogic.TV’s 18th Anniversary Contest
Don’t miss out on your chance to win a great Icom IC-705 Portable Transceiver and MFJ accessory package.
Prizes:
• Icom IC-705 HF/50/144/440 MHz Multimode Portable Transceiver
• MFJ-1982LP End Fed 1/2 Wave Antenna
• MFJ-4230MVP 12 volt Power Supply
• MFJ-915 RF Line Isolator
• RG-8X Coax (MFJ)
• MFJ-553 Deluxe Wood Base Key
Get all the details here.
https://amateurlogic.tv/contest/
