Joyce/K0JJW and I were planning a trip to Alaska to visit several of the national parks. We had some time available while in Fairbanks to do some SOTA activations. We were traveling very light, so we took minimal SOTA gear: a pair of VHF/UHF handhelds and simple antennas.

We used my newly-fashioned antenna mount on a trekking pole we had with us. The trekking pole served us as as a trekking pole for hiking, a camera monopod and now an antenna support. It provides a handy way of supporting a vertical antenna and provides a little more antenna height when held up in the air.

I checked the SOTA database to identify easy-to-access summits near Fairbanks. There are several 1 and 2 point summits in the area with easy access. We were not looking for drive-up summits but we did want an easy hike.

I found that Dale/KL7R and Peter/K3OG had been activating in the area, so I contacted them via email and they both gave me helpful advice. We were a bit concerned about getting our four QSOs on VHF, but that turned out to not be a problem. We worked Dale from all three summits and he helped rustle up a few more stations to work. We had pretty good luck just calling CQ on 146.52 MHz. And I announced our presence and need for simplex contacts on the KL7KC repeater (146.88 MHz, 103.5 Hz tone).

We activated three summits:

Chena Ridge (KLF/FN-205)

We drove up Chena Ridge Road, then took a gravel road uphill towards the summit (I think it was labeled North Becker Ridge Road). At this point, we encountered a locked gate and parked there. Some locals wandered by and said that they hike up to the top every day, so come along. The hike was easy, less than one quarter of a mile with some elevation gain. At the summit is an FAA VOR site enclosed by a chain link fence.

Pedro Dome (KLF/FN-164)

Next, we drove north out to Pedro Dome, which has a substantial radio site on top. We took Steese Highway north from Fairbanks to Pedro Dome Road, a gravel road that goes right to the top of the summit. There are opportunities to make a wrong turn on the way up Pedro Dome Road but with a little care we were able to drive to the top. Despite the fact there are plenty of radio transmitters on the summit, we did not experience any interference on 2m and 70 cm. That summit has an excellent radio horizon, so it was easy to work stations in the Fairbanks area.

Wigwam Benchmark (KLF/FN-204)

Wigwam Benchmark is a summit that pokes up just north of Fairbanks. It is a bit more difficult to navigate because it in a rural residential area with lots of twisty-turny roads. I plugged “Noel Drive, Fairbanks, AK” into google maps, which got us very close. Then we drove to where Noel Drive meets Mia Drive and operated from the road. The area is heavily wooded and we did get attacked by the famous Alaskan mosquitoes, so we made our radio contacts and escaped quickly.

Summary

At one point, I told Dale that if we made one contact from one summit, we would be happy. But, of course, we tried for more than that and got it. It turned out to be a great day running around these summits near Fairbanks and making some radio contacts. Thanks to KL7R and K3OG for the assistance!

73 Bob K0NR

The post VHF SOTA Near Fairbanks appeared first on The KØNR Radio Site.

My Summits On The Air (SOTA) activation of Pikes Peak (W0C/FR-004) on June 20th qualified me for Mountain Goat, using only the VHF/UHF bands. Mountain Goat requires 1000 activation points using the SOTA activation point system.

I’ve been working toward this goal for quite a while. I was doing mountaintop VHF activations before SOTA was even a thing. The first contact in my SOTA log is from Mount Antero in August 2011 but I started cranking up the SOTA activations in 2013 and later. I chose Pikes Peak for my qualifying Mountain Goat activation because its always been a special summit for me: I see it almost every morning (weather permitting) from my house in Monument. It is America’s Mountain, reaching to over 14k feet in elevation, standing tall west of Colorado Springs.

Most people have to wait for the mail to receive their SOTA Mountain Goat certificate. However, Steve/WG0AT created a custom award certificate that Joyce presented to me on the summit of Pikes Peak.

Some statistics from my SOTA log: I made 1557 radio contacts during 164 activations. Some of these activations were repeats of the same summit and I activated 96 unique summits.  On 9 of those activations, I failed to complete the minimum of 4 radio contacts required to receive points; so I “got skunked” on those summits (zero points).

The majority of these summits were in Colorado, but I also did some operating from California, South Dakota, New Mexico, Wyoming, Utah, Oklahoma, Nebraska, Tennessee, North Carolina, Georgia, Arkansas, Texas and (last but not least) Switzerland. Almost all of them with my awesome wife and hiking partner, Joyce/K0JJW. Take a look at the various SOTA postings on my blog for trip reports and operating tips.

Chasers

Any SOTA activator will tell you that nothing happens without chasers being there to make radio contacts. Chasers are always important but even more important for VHF due to the limited range. The list below shows my top chasers. Some of these folks are active SOTA enthusiasts but many of them are just friendly folks on the radio helping me achieve this goal. You’ll see that my #1 chaser is Joyce/K0JJW, who usually worked me on multiple bands after leaving the summit.

Thank you, Chasers, for your support!

Many people underestimate what is possible on the VHF/UHF bands, even under normal conditions. I’ve been trying to educate folks on what is possible with VHF from high locations. See The Myth of VHF Line of Sight.  Beefing up your station with a directional antenna and a little bit of power can make a big difference, even when just using FM. My best DX using VHF on a SOTA activation is a 2m CW contact from Capulin Mountain with W9RM near Olathe, CO for a distance of 257 miles.

The Summits On The Air program is a fantastic way to enjoy the outdoors while having fun with ham radio. Thanks to everyone that helped me reach my goal of VHF Mountain Goat.

73 Bob K0NR

The post Summits On The Air VHF Mountain Goat appeared first on The KØNR Radio Site.

For the ARRL January VHF contest, I did a combination Summits On The Air (SOTA) and contest entry. I am recovering from a knee injury so Genesee Mountain (W0C/FR-194) turned out to be a nice easy hike for me. Of course, Joyce/K0JJW joined me and also did a SOTA activation. Caleb/W4XEN came along with us and activated the summit for SOTA using the HF bands. Finally, Brad/WA6MM showed up on the summit for a social visit.

To get to the Genesee Mountain, go west on I-70 from Denver, take Exit 254 to the south. Turn right onto Genesee Mountain Road and head into Genesee Mountain Park. There is an extensive trail system in the park and several different ways to reach the summit of Genesee Mountain. In fact, if the gate is open, you can drive right to the summit. The route we took starts at a parking area that is always open. With only a 0.7 mile hike (300 feet vertical), this is an easy and highly-recommended trail.

Leaving the parking area going uphill, we soon encountered the Genesee Mountain Trail which we followed to the left. Later we transitioned to the Genesee Summit Trail, which goes to the summit. Both of these are well marked but you need to make sure you catch the “summit” trail.

We took more than the usual set of equipment for this activation so that we could cover the 6m, 2m, 1.25m and 70cm bands. For FM, we set up a Yaesu FT-90 2m/70cm transceiver with a ladder-line J-pole hanging from a rope in a tree. This omnidirectional antenna does not have any gain but I figured that for FM it would be most efficient to not mess with having to point a yagi antenna. For 2m and 70cm ssb/cw, I used a Yaesu FT-817 driving an Arrow II dualband antenna. The FT-817 also handled the 6m band, driving an end-fed half-wave wire antenna supported by a fishing pole (HF SOTA style). For the 1.25m band, I just used an Alinco handheld radio.

Genesee Mountain is a popular SOTA summit because it is so easy to access but still provides a good outdoor experience. We encountered a dozen of so hikers and mountainbikers on the summit and it can be very busy during a summer weekend. The summit is wide and flat with plenty of room to set up a portable station. For VHF, it has an excellent radio horizon to the front range cities.

Joyce made 14 contacts on 2m and 70cm FM. I made 52 QSOs, as shown in the table below. SSB activity was relatively light considering it was a VHF contest weekend. I was pleased to work Jay/W9RM in DM58 on 2m SSB at a distance of 167 miles. W9RM is on the other end of the state with many mountains blocking the path. I also worked Jim/WD0BQM in Mitchell, NE (DN81) on 2m CW, at a distance of 175 miles. VHF is not limited to line of sight!

    Band   Mode  QSOs     Pts  Grd  
      50  USB      5       5    2   
     144  CW       1       1    1   
     144  FM      19      19    2   
     144  USB      7       7    2   
     222  FM       3       3    1   
     432  FM      15      30    2   
     432  USB      2       4    1   
   Total          52      69   11   
        Score : 759

We had a great day on the summit, operating for just under 4 hours (with lots of breaks along the way). Thanks to Caleb/W4XEN and Brad/WA6MM for joining the fun. If you are looking for your first or an easy SOTA activation, give Genesee a try.

73 Bob K0NR

The post Genesee Mountain: SOTA and VHF Contest appeared first on The KØNR Radio Site.

One of our favorite summit hikes along the front range of Colorado is Devils Head lookout tower (W0C/FR-051). This hike is about 1.5 miles one way with 900 feet of vertical gain. See my summer trip report from July 2012 for more information on the hike. This year we activated the summit in winter.

One problem with this trail is that it has become extremely popular in the summer months. The actual summit and lookout tower is not very big and can get very crowded. This is tolerable for hiking but can make a Summits On The Air (SOTA) activation difficult. It certainly is not a “get away from it all” experience.

Recently, Brad/WA6MM pointed out that the summit is still accessible now (in late November) and the crowds have all disappeared. Note that the trailhead will be difficult to access starting December 1st (see the Devils Head  forest service page).

We took highway 67 out of Sedalia, then south on Rampart Range Road (FS 300) to the well-marked side road that goes to the trailhead . The forest service roads had 6 to 8 inches of snow on them but we were able to drive our 4WD pickup truck to the trailhead without any problem. The trail was also snow covered but walking in high-top hiking boots worked just fine. We had our microspikes along in case of ice but did not use them.

As you can see from the photos, it was a bright sunny day…wonderful day to be out hiking in the mountains. Temperature was about 25 degrees F but very light wind.

We met a total of four other parties on the trail, so not very busy.

Once on top, we started calling on 146.52 MHz with many stations responding. That summit has good line-of-sight to Denver and the other front range cities. As things quieted down on 2 meters, I switched to 446.0 MHz and worked a bunch of stations there, too. We were using the small TYT 2m/70cm mobile transceiver (which I recently repaired) and yagi antennas for 2m and 70cm. I also had my 23cm HT and Comet yagi with me and managed to work Paul/W0RW on 1294.5 MHz, about 33 miles (53 km) away in Colorado Springs.

Here is my log from the activation:

Joyce worked a subset of these stations. In particular, she was very happy to work three women. She has been referring to these contacts as “F2F” for “female to female.” On this activation, her F2F QSOs were: Annette/KA0JKZ, Sharon/KC0PBR and Barbara/W0BJE. Way to go, ladies!

We’ve made a note to do this summit again next year, after the crowds are gone. It is a really nice early winter hike. Thanks to everyone that worked us on the summit.

73 Bob K0NR

The post Winter SOTA on Devils Head (W0C/FR-051) appeared first on The KØNR Radio Site.

Joyce/K0JJW and I were planning a trip that included some time in Europe. It turned out that our airline route would connect through Zurich. Rather than spend a few hours in an airport, we decided to spend a day or two in Switzerland.

Somehow the discussion turned to Summits On The Air (SOTA) and whether we should do an activation in Switzerland.  Slowly, a plan developed to do a “check the box” activation on a local summit near Zurich. As readers of this blog know, I’ve been exclusively using VHF/UHF for SOTA activations. We decided to pack really light so SOTA gear on this trip was extremely limited: 2m/70cm handhelds and vertical antennas. Sorry, no yagi.

SOTA Help

I came across this thread about the proper callsign prefix when operating under CEPT rules in Switzerland. The SOTA association is called HB but valid callsign prefixes are HB9 (full license) or HB3 (novice license). This sent me back to the CEPT rules to make sure I understood them correctly:  Recommendation T/R 61-01 and ECC Recommendation (05) 06. The short story is that as an Amateur Extra licensee, I operate as HB9/K0NR. Joyce has a General Class license which corresponds to the “novice” category under CEPT, so she uses the callsign HB3/K0JJW.  Apparently as an Extra, I had previously overlooked or forgotten some of the fine points of CEPT. Specifically, US Extras are given full privileges by CEPT but Generals can only operate in a subset of CEPT countries while Technicians get no privileges at all (yet another reason to upgrade your license).

I also put out a request for advice on the SOTA reflector:

Joyce/K0JJW and I have one day in Zurich later this month. Somehow the idea of squeezing in a SOTA activation while in Switzerland made it onto the itinerary.

This will be on 2m FM only with basic gear. The current plan is looking like a hike up Altberg (HB/ZH-015) but we are open to other ideas.

A number of people responded with helpful information. Soon I was contacted by Paul/HB9DST who suggested we do an activation together. Paul is an American living just outside of Zurich (his US callsign is AA1MI) and is very active in SOTA. We soon had our eyes on the Churfirsten SOTA summits which are southeast of Zurich (see Paul’s activation reports).  Ultimately, we chose the summit of Selun (HB/SG-049).

Activating Selun (HB/SG-049)

Access to the trail was via several train rides and a bus ride, then a short walk to the Selun cable car. This cable car is quite unique in that it is a homebrew design (see the photo below). We piled into the cable car and rode it to where the real hike started.

On the Trail

The bottom station of the cable car is at ~3000 feet (900 m) and took us up the hill to ~5000 feet ( 1500 m), so it definitely sliced off some elevation gain. The summit of Selun is at 7234 feet (2205 m), which gave us a moderate but not crazy difficult hike. My GPS app recorded a distance of 1.7 miles and 1900 vertical feet (one way).

The weather was excellent for late October with blue skies above and some clouds laying in the valleys.

Paul is an HF/CW enthusiast so that made sharing the bands very easy. He strapped his fishing pole to the summit cross and strung out an end-fed wire for 40m, 30m and 20m, making a total of 40 QSOs. Joyce and I took turns on 145.550 MHz FM using our Yaesu FT-1DR handheld radios with vertical antennas.

I made 13 contacts on VHF, including three Summit-to-Summit (S2S) contacts. HB9PMF was close by on SG-017 (Hinterrugg) another summit in the Churfirsten. I also stayed on the summit while Joyce and Paul hiked down out of the activation zone and worked me for chaser points, giving me a total of 15 QSOs.

My log is shown below. All contacts were on 145.550 MHz. Note that the calling frequency in Switzerland (all of Europe?) is 145.500 MHz. Joyce worked a subset of these stations.

Operating notes

I have to admit that it was a challenge keeping everything straight while making QSOs. I had to add the HB9 prefix on the front of my US callsign and “portable” on the tail end (local practice for activator stations). That’s “HB9/K0NR/P” instead of just “K0NR”…there is a reason we prefer shorter callsigns. All that along with the usual signal report, name, SOTA designators, etc. Fortunately, everyone we worked had reasonable English skills. Mein Deutsch ist nicht so gut. If I sounded a bit confused, I probably was and at 7200 feet I can’t blame the altitude.

It was definitely a thrill to work the S2S stations and two other countries (Germany and Austria) on VHF. (I have never done that on SOTA VHF from Colorado…I rarely work anyone outside of the state.)

After we hiked back down, Paul suggested that we had to stop in at the local farmhouse restaurant (Selun Ochsenhuette) for a drink. It was all part of the Swiss SOTA experience!

Paul was a magnificent host for our short stay in Switzerland. We stayed two nights at his place and he guided us on a fantastic SOTA activation.  Without his help, we would have probably activated a small summit near Zurich and would have been in the low clouds all day. We would have left the city thinking “I bet this is a beautiful place when the sun is shining.” Instead, we had an excellent day hiking the Swiss mountains and playing ham radio. Thanks, Paul!

Joyce did find one small way to repay Paul’s kindness. Being an skilled seamstress, she sewed Paul’s prized SOTA Mountain Goat patch onto his pack. Nice job, Joyce!

73 Bob K0NR

The post SOTA Activation in Switzerland (HB/SG-049) appeared first on The KØNR Radio Site.

There is a SOTA (Summits On The Air) summit just north of Tincup Pass with an elevation of 13,538 feet. The SOTA database (W0C/SP-127) says the name is Mount Emma but all of my maps indicate that it is Emma Burr Mountain. (I contacted the W0C Association Manager and we’re working it out.)

Joyce/K0JJW and I did the first activation of this summit in late September. The weather was wonderful except for the wind that pounded us anytime we were exposed on a ridgeline, which is to say it happened a lot. We started our ascent from Tincup Pass, which is at 12,154 feet on the Continental Divide (see photo). I’ve seen trip reports of people hiking this summit from the northeast (Mineral Creek area) accessible by South Cottonwood Road (FS 344), so that may be another option.

At Tincup Pass, there is an obvious trail leading off the the east. We followed this trail uphill for a while and then diverted off to the north towards the north/south ridgeline and Tincup Peak. Tincup Peak is not a SOTA summit and is not shown on all maps. It is a13,345 foot bump on the ridge heading north. Our entire hike followed the Continental Divide, always a real treat.

We followed the top of the ridge for the most part, occasionally dropping down a bit on the west side to avoid obstacles. Occasionally we followed a faint trail but for the most part this was off-trail hiking, often with significant rocks to climb over.

Once we got on top of the ridgeline, we could see our actual objective of Emma Burr (see photo below). The saddle between Tincup Peak and Emma Burr dropped down more than I expected from viewing the topo map, so we soon realized that we’d have to lose substantial elevation and then climb to get it back. Oh, well.

Once on the summit of Emma Burr, I pulled out the 2m FM station and started calling CQ on 146.52 MHz. We had no mobile phone coverage at Tincup Pass but once we got on the ridge, Verizon was working pretty well so I spotted us on Sotawatch. Our best DX was Dave/N0KM near Center, CO for a distance of 70 miles. Other stations worked: W0BV, W0RW, N1TEW, K0MGL, K0TG, KB0QEP, KL7GLK, N0EVH, KD0VHD and W0DLE. Lots of stations on 2m FM that day. I tried working W0RW on 1.2 GHz FM but we could not quite make it. I definitely heard him right at the noise floor but my 1 watt signal was not readable on his end.

My GPS app on the smartphone says that the one-way climb is 2.4 miles with 1600 vertical feet. The elevation difference between Tincup Pass (12,154) and Emma Burr (13,538) is 1384 feet, but the saddle costs you another 300 vertical feet of climbing.

Overall, it was a great day in the mountains. We knocked out two 13ers in one day and did a first SOTA activation. However, the wind pounded us quite well so we were plenty tired when we got back to our vehicle.

73 Bob K0NR

The post SOTA Activation: Mount Emma or Emma Burr Mountain (W0C/SP-127) appeared first on The KØNR Radio Site.

While exploring northwest Wyoming, Joyce/K0JJW and I were looking for a suitable mountain for a Summits On The Air (SOTA) activation. A little bit of research identified Pass Benchmark (W7Y/TT-122) as a good option. This summit is accessed from the Teton Pass trailhead, which is on a paved road (Route 22) heading west out of Jackson. There is substantial parking available at the pass and it appears to be a popular trailhead for hikers and mountain bikers.

The sign at the trailhead refers to this summit as Mount Elly, but I have not found that name on any of my maps or other sources. SOTA refers to it as “Pass Benchmark”.

We hiked south from the pass on an obvious gated road which later turns into a trail. We encountered several groups of hikers and mountain bikers so the trail definitely gets used and is in good shape.

We followed the trail past a radio site (and checked out the various antennas). The good news is the radio site is not on the SOTA summit, so not much chance of radio interference.

We continued south on the trail until we were due west of the summit. There is a marker there for the Black Canyon Trail, which leads off to the south. Don’t follow this trail, instead turn left (east) towards the summit. A few switchbacks will get you to the top in good shape. The one-way distance for the hike was 2 miles with 750 feet of elevation gain. Very pleasant.

On top, we started calling on 146.52 MHz with the Yaesu FT-90 putting 30W into a 3-element yagi antenna. We both worked Sam/WY7EM, Jim/K7AVL and Mick/W7CAT on 2m fm. We also caught WY7EM and W7CAT on 446.0 MHz.  Thanks for the QSOs!

73 Bob K0NR

The post SOTA Activation from Teton Pass (W7Y/TT-122) appeared first on The KØNR Radio Site.